Do-it-yourself wooden stool drawings. How to make a stool with your own hands drawings

Just one of those things that are done in 15 minutes, and then serve for years. Moreover, the master class itself to write and read even longer than to do it. Therefore, my son (a boy of 11 years old) decided to make it on his own, however, under my strict guidance. But only as a consultant and photographer.

So, a simple stool. For her, we need only four pieces of chipboard:
Two on legs, 200 by 250 mm;
One upper part - 250 by 300 mm;
And one spacer 90 by 200 mm.

All this I did not buy and did not order. And in workshops where large sheets are cut out, there are a lot of unnecessary scraps. Here they are, “thank you”, I scored plenty, and now they should turn out to be a comfortable stool made by myself.

In addition, you will need a simple device for pasting parts with an edge (you can also do without it, it’s just more convenient),


the edge itself


iron,


knife,


a piece of sandpaper fixed on a block,


hex bit for confirmations,


drills (seven millimeters and confirmed),


"His Majesty" screwdriver,


four confirmations,


five chops,


small hammer and/or rubber mallet


wood glue PVA,


and four legs.


I just had all this at home, and you may have to take a walk to the furniture fittings store. Now let's start making a stool with our own hands.
To begin with, we glue the workpieces with an edge. It's very simple, so a hot iron will help you. You can use any, even borrow a particularly fashionable one from your spouse, secretly. She won't notice anyway, and you won't spoil it. So, we glue the edge for our hand-made stool with a hot iron (a few seconds will be enough) and rub the adhesive base with a rag. The edge is very hot, so be careful not to burn yourself.


Cut off the excess, and glue the parts on the other side. Then, for complacency, go over the ends with sandpaper.


Now, with two confirmations, screw one leg to the transverse bar,


and then another. The basis for our homemade stool is ready.


Drill five holes in the lid. Not through, but in secret,


and hammer dowels on the glue. The lid for our simple stool is ready.


Mark five holes, drill them too, pour glue, and connect both parts into a single whole. Made a stool

How to make a stool with your own hands, product drawings and the progress of work on the manufacture of a small and compact model.

Dimensions:

Height - 312 (mm)
seat size - 300 x 300 (mm)

The article describes the principle of constructing a stool, the overall dimensions of which can vary depending on the methods of its use and application. The place for the seat can be made from solid glued wood. Lengthen the legs.

When designing and manufacturing a product, we will be guided by the following:

Minimum details
ease of manufacture and assembly
structural strength during operation
long-term reliability
attractive appearance

Specification of the dimensions of the material used (length, width, thickness):

Side wall 219 x 50 x 22 (mm)
front wall 268 x 50 x 22 (mm)
leg 300 x 40 x 40 (mm)

Seat bar 300 x 45 x 12 (mm)

How to make a stool with your own hands, work order:

1. Make parts from dry wood according to the specification, strictly observing their dimensions, parallelism and perpendicularity of the faces.
2. Mark the center of the mounting holes.

Reference.

As a fastener we will use:
(confirmat) - for attaching the legs to the front and side rails
– for attaching the seat trims to the front and side trims

3. Drill holes in the parts to the desired depth, while strictly making sure that the centers of the holes in the parts to be joined are on the same axial line perpendicular to the edges.
4. Connect the legs (3) to the front (1) and side (2) strips with euro screws.

5. Attach the seat slats (4) to the assembled frame with wood screws.

6. Clean up the product.
7. Apply a protective decorative coating to the product.
8. Close the euro screws with plastic plugs. Match the color of the plugs to the color of the decorative coating of the product as much as possible.
9. If necessary, put your trademark or brand on the product.

The stool is done. Design requirements are met. You can install a bowl on it and send it under

A stool is one of the simplest types of furniture. Whatever changes our life has undergone, it remains unchanged. Only the materials from which it is made change. In Soviet times, making a stool with your own hands was one of the first tasks in labor lessons. Carpentry was known not only to boys. Sometimes the fair sex also had to comprehend the basics of adult life and learn how to make a stool with their own hands. Modern furniture bears little resemblance to its counterparts 50 years ago. Wooden stools of that time were rough, but durable. They fit perfectly into the interior of the kitchen, as well as other rooms. Now the stores have a rich assortment of different types of furniture, but there are also lovers who want to learn how to make a stool with their own hands. And in our time of abundance of building materials, it will not be difficult at all.

The main parts of the stool are the seat and legs. The legs are connected at the top with tsargs, and at the bottom with prolegs. Having mastered the terms, you can do the drawings. First, you need to decide on the size. When making a stool, it is better to build on old, but reliable models that can be found in every home. Having measured the height and other parameters, you can begin to develop a circuit. If you do not have a sample, then for an adult stool the size of the side of the seat will be 300-450mm, for a child - 250-280mm. Homemade stools should be even more convenient than purchased ones. At least because you can choose the height for yourself. Usually the size for an adult is 420-480mm, for a child - 260-280mm. Drawings of stools must be carried with you, whether it is a diagram from the Internet or compiled by you. After all, it is much easier to eliminate shortcomings on paper than to redo all the work.

Materials and tools

Making a stool will require quality materials that have stood the test of time. In the first place, of course, wood. Wooden stools are in first place in terms of convenience and in second place after forged ones in terms of durability. The tree should be dried at room conditions at 20-30 degrees, a chamber-drying tree should not be taken, since the possibility of cracking is not ruled out. After air drying, the material must be dried at home at room temperature for about a month. It is best to take hardwood: maple, birch, beech, wenge, hemlock, mahogany. Or make legs out of them, which carry the main load, and a seat made of pine, spruce, MDF, chipboard or plywood.

Chipboard is one of the cheapest, but unreliable materials. It has advantages, such as moisture resistance. But in the manufacture of a stool, strength is much more important, and it is insufficient for chipboard, and besides, it is too fragile for furniture, although there are a couple of options in which pressure on chipboard can be reduced. But the constant release of formaldehyde resins, which make this material unsafe, unfortunately, cannot be completely eliminated.

MDF is an eco-friendly material, durable enough. However, when making furniture for the kitchen with your own hands, it is better to use it in combination with hardwood, especially in supports, that is, in fact, it is taken only on the seat, or cover, as it is called in some sources.

A good substitute for wood is plywood, but then you have to "conjure" a little with the design. From plywood, stools for the kitchen are obtained from 3 parts, or from 4, the so-called box-shaped ones. This design is now very common, especially in the furniture industry. Although it is perfect for making a stool with your own hands.

Tools are selected depending on the materials. To make wooden stools, we need:

  • roulette
  • self-tapping screws
  • screwdriver
  • square
  • jigsaw
  • chisel
  • emery
  • joiner's glue

How to make a classic stool

In order to make a wooden stool with our own hands, we need material (boards, bars) and tools. If there is no electric jigsaw and there is no way to purchase it, then we do this: we buy an inexpensive frame hacksaw for metal and direct it with teeth towards us when working. So, the scheme is ready, the materials are purchased, and, if necessary, dried, the tools are prepared - you can start. Before starting work, you can make so-called “patterns” out of paper, that is, life-size details of the future stool cut out of paper. You can not do this, whichever is more convenient for you.

Click to enlarge

We start with the legs, we will have them with a square section of 50x50mm. Let's saw off 4 identical parts from a bar, let's say 450mm long. Then, from a single piece or from two halves, assemble a seat, we have 380x380, the thickness of the board is 20 mm. Next, cut out 4 drawers to connect the legs of the stool and 4 legs. We also need four bars for additional connection of the tsarg and the seat. The design is assembled according to the principle: tenon-groove, the spikes are cut along the edges of the tsarg, and the grooves on the legs of the future stool. The length of the spike and the depth of the groove is approximately 20-25mm. We do the same with the prolegs, which will subsequently be attached to the legs. You can mark the details ahead of time for clarity.

We process with emery before the parts are assembled, this is both convenient and safe. We assemble all the details at the beginning without glue, adjusting and, if necessary, filing them. Then we coat the parts one by one with glue and assemble them. We fasten the bars between the sides with self-tapping screws to the bottom of the seat "close". To do this, take care of the length of the fastener in advance. I would like to say a few words about the glue with which we will coat the grooves.

Glue is better to take a special, carpentry. This glue has proven itself for many years. If it is not there, then you can take PVA, but not stationery for paper, but one that is suitable for wood.

Other types

There are stools that will be much easier to manufacture than the classic one. A very common option now is a stool, consisting of four parts: a seat, two wide legs and a reinforcing crossbar (or jumper). This option should not be difficult, especially in the assembly. Wood, thick plywood, and laminated chipboard are suitable for it. They fix this design with furniture screws and glue for additional fixation. This option is very simple, but there is one subtlety: the reinforcing bar should be in the shape of a trapezoid with a 5mm bevel. This is necessary in order to make the structure more stable.

You can try your hand at making a lightweight stool. In this version, there are no drawers and the legs are attached directly to the grooves of the seat. To do this, the seat cover is made of thick material. The grooves are made directly in the seat or bars are attached to it. In this case, the legs are made thicker than usual. Of course, such a stool will take much less time than a regular one.

Another type of stool is a seat and two legs arranged crosswise at an angle of 90 degrees. In this option, there are no additional parts, where the design itself consists of 4 parts. In this case, we can again use wood, plywood, and pressed boards. If we stop on a wooden model, then we do the final touch after the final assembly. We carefully grind the stool again, and then we process it as we wish with stain, varnish or paint.

Making your stool

Your stool can be arranged depending on the interior items where it will be located. You can apply a spray paint pattern to the surface of the seat using a stencil. Then varnish the surface. Or make a bold design move and decorate a retro stool using decoupage. It is time-consuming, but effective, besides, you can involve the whole family in this interesting business. To do this, we need PVA stationery glue, beautiful napkins and varnish, preferably acrylic. The result will tell not only about your accuracy, but also reveal your taste. In the end, you can only decorate the seat by laying thin foam for softness. Then decorate it with a beautiful fabric and decorate with accessories to taste. As they say, everything is in your hands!

When purchasing furniture, you can notice a clear discrepancy between the prices of materials for their manufacture and the final price of the product. This is especially striking when buying fairly simple pieces of furniture, such as stools.

Stools are most often made from chipboard.

Stools are most often made from chipboard. It is a fairly cheap material, easy to work with, durable and great for indoor use. Having looked once at a chipboard stool, it is easy to understand that it is quite easy to make it with your own hands. We suggest that you familiarize yourself with the detailed instructions for the manufacture of various configurations of stools at home.

Having looked once at a chipboard stool, it is easy to understand that it is quite easy to make it with your own hands.

You can make a stool with your own hands, having at hand professional and non-professional elements and devices.

Required tools include:

  1. electric jigsaw, complete with a small file;
  2. screwdriver

To decorate the stool seat, you can also prepare foam rubber and upholstery.

You may also need a drill with a drill and a stapler for construction purposes.

The upholstery can be fabric, oilcloth, leatherette.

To simplify the assembly task, you can first glue the parts, and only then fix them with self-tapping screws.

Materials for manufacturing:

  1. chipboard sheets, new, substandard or remaining spare parts from old furniture;
  2. self-tapping screws, no longer than the thickness of the chipboard;
  3. confirmations 4 pieces. Size 6.4 mm by 50 mm;
  4. metal corners 4 pieces;
  5. adhesive tape for processing the edges of sheets;
  6. thrust bearings of any acceptable materials;
  7. sandpaper for sanding.

Creating a stool from chipboard with your own hands allows the master not to limit himself to standard models.

Non-professional tools that can be found in any home:

  1. pencil or marker;
  2. cardboard for making templates;
  3. ruler or tape measure;
  4. a knife of any configuration, the main thing is sharp.

It would seem that the simple design of the stool has several dozen different models.

Parts of the stool are assembled using confirmations and self-tapping screws.

To decorate the stool seat, you can also prepare foam rubber and upholstery. The upholstery can be fabric, oilcloth, leatherette.

Illustrative examples can be found in furniture stores, from neighbors or on the Internet.

Create a project

Creating a stool from chipboard with your own hands allows the master not to limit himself to standard models. It would seem that the simple design of the stool has several dozen different models. Illustrative examples can be found in furniture stores, from neighbors or on the Internet.

Usually, several pieces of stools are needed at once, so it is extremely important to choose one shape you like and make identical items according to the selected drawing.

When starting the final assembly of parts, it is necessary to pre-treat all cut edges with a special tape.

Usually, several pieces of stools are needed at once, so it is extremely important to choose one shape you like and make identical items according to the selected drawing. When making a drawing, it is important to remember that the design of a stool requires a clear balance between its lower and upper parts. A discrepancy between the dimensions of the seat and the width of the legs can lead to an imbalance, as a result of which the object will be very unstable, and therefore traumatic.

When making a drawing, it is important to remember that the design of a stool requires a clear balance between its lower and upper parts.

Choosing a material for manufacturing

Stools can be made from different materials. Chipboard, multi-layer plywood, wooden blocks and boards are suitable. The cheapest and most unpretentious material to work with is chipboard. Sheets can be purchased at the store, at furniture factories, or you can buy trimmings from small firms that make furniture to order. Sheets of old chipboard, which were previously parts of other furniture, are also suitable.

A discrepancy between the dimensions of the seat and the width of the legs can lead to an imbalance, as a result of which the object will be very unstable, and therefore traumatic.

The final touch in preparation before assembly will be drilling the necessary holes.

We apply graphic markup

Stools can be made from different materials.

Having decided on the model of the future stool, it is necessary to mark out a chipboard sheet, thereby preparing it for further work. If you plan to make several identical stools, then it is better to make a pattern for all parts of the furniture. The template is conveniently made of thick cardboard.

For further ease of use of the manufactured furniture, the corners of the parts should be rounded. It is better to make even roundings with a compass. The absence of this item can be compensated, for example, with a plate of a suitable diameter.

The cheapest and most unpretentious material to work with is chipboard.

High speed will ensure cutting of sheets without chips and notches.
After trimming, it is necessary to clean all the edges of the stool with sandpaper.

Depending on the selected shape and model, the dimensions of the elements may be as follows.

No. Stool model Seat dimensions Legs dimensions Crossbar dimensions

  • 1 30x30 30x40 20x12
  • 2 30x40 30x40 30x15
  • (3 pieces)
  • 3 40x40 20x35 (8 pieces) 30x20
  • (4 pieces)

Sheets of old chipboard, which were previously parts of other furniture, are also suitable.

Cut out elements for the future stool

The main thing is to determine in advance the number of pieces of finished products, and calculate the required volumes of materials.

Cutting elements from existing pieces of chipboard is done using an electric jigsaw.

Cutting elements from existing pieces of chipboard is done using an electric jigsaw. You can make a good cut of the edge using a small file and a high speed jigsaw. High speed will ensure cutting of sheets without chips and notches.

After trimming, it is necessary to clean all the edges of the stool with sandpaper. Such processing will ensure a good fit of one part to another and simplify assembly.

The final touch in preparation before assembly will be drilling the necessary holes. Make sure that the holes are drilled at the same level.

Having decided on the model of the future stool, it is necessary to mark out a chipboard sheet, thereby preparing it for further work.

We collect a stool

When starting the final assembly of parts, it is necessary to pre-treat all cut edges with a special tape. The tape must be chosen to match the color of the sheet or vice versa in contrasting shades.

The tape is applied to the cut of the legs and the seat and glued with a hot iron. The iron must be applied with quick and short movements. The warm tape should be pressed down with a clean cloth. The glue, which is on the back of the tape, sets very quickly and does not require long warm-up or cool-down.

Parts of the stool are assembled using confirmations and self-tapping screws. To simplify the assembly task, you can first glue the parts, and only then fix them with self-tapping screws.

The seat of the resulting chair can be made soft due to foam rubber and upholstery.

For further ease of use of the manufactured furniture, the corners of the parts should be rounded.

It is better to make even roundings with a compass.

VIDEO: Do-it-yourself stools from chipboard scraps.

50 photo ideas on how to make a stool with your own hands from chipboard

A stool is an integral element, a must-have fixture in any home. You can't call it too expensive or rare to be taken for hand-made, but a hand-made stool is sure to be more durable and elegant than a standard product from any store. This is what we will talk about today.

As with any more or less serious work, you need to be well prepared to create a stool.

List of required tools

The first step is to prepare all the tools that you might need. You need to prepare different tools, as we will look at various photos of stools, from which you can do the work yourself.

The list looks something like this:

  • jigsaw;
  • drill;
  • screwdriver;
  • screwdriver;
  • drill;
  • sandpaper, and ideally a grinder;
  • fine-toothed hacksaw;
  • pencil;
  • ruler or corner.

Materials for making a stool

In addition to tools, of course, you will also need materials for making a stool. Their list can be limited to the following items:

  • marker;
  • roulette;
  • timber;
  • slats;
  • plywood
  • foam rubber;
  • the cloth;
  • buttons, nails, screws.

Possible stool options

Since stools are considered a fairly common option for seating devices, there are many varieties of them. We believe that it is necessary to consider the most convenient and popular ones in order to know for sure what you can do with your own hands.

The most popular options are below:

  • in the form of an ordinary chair;
  • small stool suitable for balconies and for use as a stand. Often has a height of no more than 25 centimeters;
  • upholstered stool. It resembles an ordinary stool in the form of a chair, but due to the presence of soft upholstery, it is often used in modern kitchens;
  • folding option. The well-known folding stool, on which grandmothers sit in the markets, fishermen fishing and summer residents in summer cottages.

To dot the "i", we suggest you look at the photos of the stools that we have given in the classification.

The stool, which we want to consider first, is ideal for both the kitchen and the glazed loggia, where you can sit down to relax and drink tea. It will have crossed legs, fastened with timber for greater structural stability. The seat of the stool will be covered with fabric, under which foam rubber will be located. This upholstered stool is the perfect seat for any kitchen.

Naturally, in order to do everything right, it’s not enough just to follow the instructions, you need to carefully study the drawing, which we recommend that you do.

Characteristics of the bars

To make a stool, we need to prepare the bars. Their characteristics will be as follows:

  • the length of the bars from which the legs will be made is 48 centimeters;
  • the location of the intersection of the legs is 24 centimeters from either side.

Making a wooden stool

We make legs and base

The first thing you need to take on is the legs of your future stool. Let's get down to business:

  1. Take a pre-prepared beam and saw off 4 special blanks from it, the length of which will be 60 centimeters each.
  2. Make saw cuts that will be directed at the correct angle of 45 degrees.
  3. Use a special miter box to saw off the legs, which can guarantee you exactly the right angle. So you will not waste valuable materials and redo the wrong work.
  4. After making four legs, they must be fastened in pairs.
  5. Make special grooves located at the intersection of the legs. Observe the depth of the groove at half the width of the leg.
  6. When the grooves are made, the legs must be extremely accurately installed in them, without going beyond the boundaries. As a result, you will get a cruciform blank. Or rather, there will be two of them.
  7. It's time to work on the stability and strength of the future chair. To do this, you need to make a special bar that fastens the crosses of the legs together. The length of the beam will be the same as your future stool. And if you make a stool, the diagram of which was placed above, the size of the beam should be 60 centimeters.
  8. Prepare special grooves for the screw heads that will hold the fastening beam on both sides of the cross legs.
  9. Fasten the crosses together by screwing the groove to their centers with screws.
  10. Fill the slots for the screw heads with wood filler so that the fastening points are not visible.
  11. But strengthening the legs in the area of ​​​​their crossing is not enough. You also need to fasten them with bars and at the top. Similarly, use screws (2 for each of the crosses) with which to attach the bars of equal length to the cut at an angle of 45 degrees, the parts of the legs located on top.
  12. Seal up the screw holes to make them invisible.

The legs are ready and it remains for you to paint their base in the color that you like best.

We perform sitting

When making a stool for the kitchen, a soft seat is something that must be present in its design. Luckily, it's not that hard to make.

In order to make a durable seat, you need plywood. Its thickness is not too important, but a thickness of less than 12 millimeters is not recommended, since such a seat will be too flimsy.

Let's get down to business:

  1. Take a circular saw, a jigsaw or a good old saw, and cut out with their help a rectangular piece of plywood, the dimensions of which will correspond to the dimensions of the chair base. In our case, it is 60 by 40 centimeters.
  2. Take scissors and cut off a piece of foam rubber, the size of which will be equal to the size of the seat itself.
  3. Next, cut off the lining material. As for its size, it should exceed the size of the seat itself by about 30 percent. Such a reserve is made in order to be able to fix the matter under the seat in the future.
  4. Lay out the prepared materials in the following sequence: matter, foam rubber, plywood.
  5. Fold the corners of the fabric under the cover of the future stool.
  6. Take the material that will serve as the upholstery for your chair. It must be put on the seat from above, and attached from the bottom side with the help of special buttons. Buttons with plastic caps are ideal. They look quite aesthetically pleasing while holding matter in place very securely.

Congratulations, the part you will sit on in the future can also be considered finished.

We collect a wooden stool with our own hands

Finally, a few details of the future stool, your own production, are assembled.

But by "assembled", we mean that they are made. And now they have to really be assembled so that the stool can begin to be used.

Let's just say - the work is very simple. You just need to attach the finished base to the seat.

  1. Get the right screws.
  2. Use them to attach the seat to the base of the future stool.
  3. Use 2 screws on each side.
  4. If desired, you can mask the heads of the screwed screws with wood filler.

Your kitchen stool is made and ready for a long and reliable service.

DIY folding stool

Everyone knows what a folding stool is, and this, by the way, has been known for a very long time. This is an indispensable assistant for fishing, outdoors, this is something that you cannot do without in the country. And instead of going to the market and spending money on a stool of suspicious quality, you can also make it yourself.

Stool: dimensions and drawing

The design of such a folding chair is painfully simple, but still, it is necessary to use the drawings so that everything comes out clearly and without unnecessary snags. Therefore, we offer you the ideal drawing for consideration.

Necessary materials

To create all the necessary elements separately and assemble them into a single whole in the end, you will need the following devices:

  1. Completely identical bars in the amount of 4 pieces. Their parameters should be 47 by 4 and 2 centimeters in length, width, and thickness, respectively.
  2. Overhead prolegs with parameters of length, width and thickness - 32, by 4, by 2 centimeters.
  3. Crossbars under the seats in the amount of four pieces. Overall parameters are the same as for prolegs.
  4. Bars that will play the role of a seat. They also need four. The length is 35 centimeters, and the thickness is 2 centimeters. As for their width, 2 bars should be 6 centimeters each, and 2 more - 9 centimeters each.
  5. Bolts - 6 pcs. The length of the bolts should not exceed 4 centimeters, including the cap. The diameter should be 6 mm.
  6. Self-tapping screws 45-50 millimeters.

How to make a stool from prepared materials

When all the materials and tools are collected, you need to start making a chair.

  1. The very first thing that is required of you is the placement of the axle bolts. They are fixed on the legs of the chair, but by no means in the middle of each of them. This is an erroneous opinion about fixing the bolts exactly in the center. In this case, the stool will turn out to be high, and will not differ in stability characteristics. It is recommended to drill holes for the bolt closer to the top of the legs.
  2. When drilling a hole for the bolt, do not forget also that its head must be drowned in the hole. Anticipate this moment.
  3. Attach the crossbars under the seat to the upper ends of the legs of the stool with bolts. Please note that there are four crossbars, and two of them must be connected to the inner legs, and two more to the outer ones.
  4. In the case of correct assembly, you will get hinged parts in the amount of two pieces.
  5. These parts must be connected using wide seating bars. But do not forget to leave small overhangs from 1.5 to 2 centimeters.
  6. The fastening of the bars occurs in the following way: one of the bars is attached to the ends on the inner crossbars, and another one is attached to the two outer partitions.
  7. Now you need to install the prongs. They are installed at a distance of 10 cm from the bottom of the legs. After proper marking and installation, they should be fixed with pre-prepared screws.
  8. Moving on to the next step, you will need to secure the middle bars. This operation must be carried out slowly, having thought through and calculated all the points. All because it is a very painstaking work. The fact of how convenient and free your future stool will be assembled / disassembled will depend on the correct installation of the bars. The middle bars are located similarly wide and outer, one for the inner and outer crossbars.
  9. The height of the future stool will directly depend on the place where the internal bars will be connected. The ideal location for their attachment is 15-20 millimeters from the bars of a wide-type seat. If you follow this scheme for manufacturing the product, its height will be about 35-40 centimeters. Naturally, you can use other parameters, based on your own wishes.

Suitable materials and a small nuance

In the process of making a folding stool, in general, you can use almost any type of wood. But mainly pines or birches are recommended. By the way, a pine stool will have a very small weight, which is convenient for carrying it often, for use on fishing trips and to the country. True, such a pine stool tends to loosen quickly, and requires periodic tightening of the bolts that hold the structure together.

There is another interesting design refinement that will make an already convenient device even more convenient. You can attach a portable handle to the structure of a folding stool. Such a handle is fixed between the inner legs. If you initially take bolts not 4 centimeters each, but 6-7 each, a very convenient handle for carrying the product can be fixed between the inner legs.

Making a stool with your own hands. Video

At the end of our conversation, so to speak, in order to reinforce the work done, we offer you an entertaining video that tells you how to make a stool with your own hands.

The video describes in detail all the nuances and subtleties of making a high-quality, durable and reliable chair at home. After spending half an hour of your personal time, you will finally figure out all the necessary operations and will be able to get to work with confidence. After all, it is not for nothing that they say that you can read it 10 times, but having seen it once, you will surely know how everything is done.
Loading...Loading...